Since the early 1970s, automotive manufacturers from around the globe have strived to slash their vehicles’ emissions output. In fact, such efforts were forced at the hands of mounting legislation, bent at governing noxious output from automotive exhaust. However, cleaning up such output was no easy task, and required the development of new emissions control technology.
Looking for a good online repair manual? Click Here for the 5 best options.
Today’s modern emissions control devices tend to be quite reliable, providing years of trouble-free service. However, much like any mechanical component, even these devices carry an expected service life, and will eventually wear out with the passage of time. When this occurs, a fault code is often stored, leading to the illumination of a vehicle’s check engine light.
One such emissions-related fault code that is common among various vehicle models, is DTC P0443. This code is largely indicative of a failure within a vehicle’s evaporative emissions system and is generic across all makes of vehicle.
Read on to learn more about diagnostic trouble code P0443, as well as how to diagnose and remedy the root cause of such issues.
Table of Contents
What Does Code P0443 Mean?
OBD-II Trouble Code P0443 DescriptionEvaporative Emission Control System Purge Control Valve Circuit Malfunction
Diagnostic trouble code P0443 indicates that a vehicle’s PCM/ECM has detected a fault within the purge control circuit of a vehicle’s evaporative emissions control system. However, to fully grasp the meaning behind DTC P0443, one must first understand how a vehicle’s evaporative emissions system operates.
Today’s vehicles feature an evaporative emissions system, which is intended to catch gasoline vapors, thereby preventing them from escaping into the atmosphere. Simply put, a vehicle’s evaporative emissions system forms a closed loop, in which gas vapors are stuck, rather than being vented externally.
In a properly operating evaporative emissions system, these vapors are gradually fed into an engine’s intake, where they are eventually combusted. This feat is accomplished by metering these vapors through a purge control valve. This valve is actuated through the delivery of ground (-), via an engine’s ECM/PCM.
As such, diagnostic trouble code P0443 indicates that the affected vehicle’s ECM/PCM has detected a fault within the purge control valve’s operating circuit. Therefore, this would indicate that the vehicle’s purge control valve is operating in an irregular fashion, or is unable to operate at all.
Symptoms of Code P0443
The exact symptoms associated with DTC P0433 often differ on a case-by-case basis, and can vary from one model of vehicle to the next. However, several symptoms tend to be far more common than others, affecting a larger percentage of vehicles plagued by an active P0442 code.
The following are the most common symptoms associated with DTC P0442.
It is also worth mentioning that a number of vehicles exhibit no additional symptoms in connection with DTC P0443. In such cases, the sudden illumination of a check engine light might serve as the only indicator that an issue actually exists.
Causes of Code P0443
The onset of diagnostic trouble code P0443 can be caused by a number of underlying issues, which often vary from one make and model of vehicle to the next. Nonetheless, there are several issues that tend to account for the lion’s share of P0443 conditions.
The following are several of the most common causes of DTC P0443.
- Faulty purge solenoid
- Worn or damaged circuit connector
- Damaged or corroded circuit wiring
- PCM-related issues
Is Code P0443 Serious?
DTC P0443 is not typically classified as being overly serious. Quite the contrary, a vehicle can often be driven with an active P0443 trouble code, without the worry of additional issues.
However, in rare instances, P0443 can be accompanied by a rough or erratic idle. In such cases, one might be prompted to expedite further diagnostics and repair.
Many motorists decide to fast-track the repair of DTC P0443-related issues, due to the negative impact that a fault of this nature can have on fuel consumption.
In such instances, further diagnosis and repair of P0443-related concerns can actually save a motorist money, over being forced to fill up more frequently at the pump.
How to Fix A Code P0443
The following steps can be used as a general template when attempting to diagnose and repair the root cause of a vehicle’s active P0443 trouble code.
As always, it is also important to consult factory-specific service literature for your particular vehicle, before beginning the repair process. Doing so provides you with important data, such as torque specifications, and acceptable test ranges.
#1 – Check For Additional DTCs
Before beginning the diagnostic process, it is important to check for the presence of additional trouble codes. Diagnose and repair the root cause of any additional trouble codes, before continuing to step #2.
#2 – Command Purge Solenoid Engaged
With the use of a quality bi-directional scan tool, you will now command the affected vehicle’s purge solenoid into the engage or “open” position. If successful, you should hear one or more clicks. If no clicking noises are heard, further diagnosis will be required.
#3 – Visually Inspect For Wiring/Connector Defects
You will now carefully inspect the purge solenoid’s connector, as well as the wiring pigtail protruding from this connector. Look for any damaged/frayed wiring, and ensure that each of the connector’s pins are in satisfactory shape.
#4 – Check For Key-On Hot (+):
With the purge solenoid connector disconnected and the vehicle’s ignition keyed to the “on” position, check for the presence of 12v positive at one of the connector’s pins. If no voltage is detected, further diagnosis will be required to locate the offending open circuit.
#5 – Jump 12v (+):
If one of the purge solenoid’s pins were found to be hot (+), reconnect the connector in question, and jump ground directly to the pin opposite the solenoid’s positive feed.
If the solenoid does not engage, the purge solenoid will need to be replaced. On the other hand, if the solenoid does engage, the circuit’s ground wire should now be jumped out at its junction with the ECM, providing power directly to the circuit through the far end of this wire.
Engagement of the purge solenoid indicates a faulty ECM, while a lack of engagement is indicative of a wiring “open”.