Metal Shavings in Engine Oil (How Serious Is It?)

On certain occasions, a particular sight will catch the eye of an observant vehicle owner. Those who are meticulous toward the care of their vehicle seem to know when something is awry and warrants a closer look. While that which is observed often turns out to be of little concern, there are times when one’s findings prove to be indicative of a larger issue.

Looking for a good online repair manual?
Click Here
for the 5 best options.

Few circumstances illustrate this point quite as vividly as the discovery of shiny metallic particles in a vehicle’s oil. While many motorists do not understand the exact cause behind this abnormality, most realize that it is worthy of further investigation.

Read on to learn about the root cause behind the sudden appearance of fine metal shavings and metal flakes within a vehicle’s oil, as well as how to handle such a situation, should it arise in the future.

Table of Contents

Is It Normal to Have Metal Shavings in Oil?

fine metal shavings oil drain plugfine metal shavings oil drain plug

While the engine oil in almost any vehicle will contain small, microscopic metal particles, these particles should never be observable by the naked eye. The only exception to this rule is when these particles cling to a magnetic drain plug or other polarized objects. However, even then, such particles should be scarce in nature.

The sudden collection of metallic particles within an engine’s lubricating oil is never to be considered “normal”. Quite the contrary, this abnormality often indicates that something is amiss, in regards to an engine’s internal components or rotating assembly.

What Does Having Metal Shavings in Oil Indicate?

metal shavings in oilmetal shavings in oil

The sudden accumulation of metal shavings within an engine typically indicates accelerated wear of bearings or other reciprocating surfaces. As metal erodes away from these components, it is deposited in an engine’s oil, where it collects before being discarded during routine maintenance.

Unfortunately, once one or more of an engine’s bearings have begun to wear at an accelerated rate, irreversible damage has already been done. This pattern of wear typically continues and progresses with the passing of time. In most cases, metal shavings will be present with each subsequent oil change.

See Also: How to Remove a Stripped Drain Plug

How Serious is This Problem?

rod knockrod knock

The problem with accelerated bearing wear is that it is a never-ending cycle. As an engine’s main, rod, and camshafts bearings wear, their tolerances increase beyond that specified by the manufacturer. These tolerances are vital to engine operation, as they directly correlate to an engine’s ability to maintain proper oil pressure.

With time, worn bearings no longer hold pressure in the same manner as they did when new, thereby allowing oil to pass without resistance. This often leads to a noticeable drop in oil pressure. 

As a result of this reduction in oil pressure, an engine’s bearings are then starved for vital lubrication. This exponentially complicates matters and can lead to multi-bearing failure in short order.

In severe cases, the presence of a knocking or ticking noise can be heard during engine operation, which is largely indicative of later-stage bearing failure, as well as oil starvation to an engine’s top end.

Will an Oil Filter Catch Metal Shavings?

metal flakes on oil filtermetal flakes on oil filter

While an oil filter is excellent at catching a large percentage of metal contaminants within an engine’s oil, it is far from fool-proof. In general, an oil filter will catch the vast majority of large metal shavings circulating throughout an engine. However, many metallic particles are too small for even an oil filter to catch.

As a result, these microscopic particles continue to pass through an engine’s bearings, serving as an abrasive of sorts, along the way. With time, this can further accelerate bearing wear, especially if an engine’s oil is not changed at its factory recommended service interval

When an engine’s state of health is in question, a closer look at a used oil filter can also prove valuable. In these situations, many mechanics will carefully cut the canister portion of an oil filter, to reveal its inner paper element.

This element can then be inspected for metal fragments and shavings, thereby providing clues to the overall health of an engine’s bearings and wear surfaces.

What To Do If You Find Metal Shavings in Your Engine Oil

pulling engine outpulling engine out

The discovery of metal shavings in your engine’s oil is definitely cause for concern, and should not be taken lightly. In any event, further diagnostics will be necessary.

In most cases, this will involve removing the engine’s oil pan and bearing caps, in order to carefully inspect the bearing surfaces for wear. If surface scarring or accelerated wear of any type becomes evident, a much greater issue is at hand.

Unfortunately, an individual’s options are limited when faced with rapidly deteriorating bearings within an engine’s rotating assembly. In the bulk of cases, engine removal and overhaul will be required. This can become a quite expensive undertaking, to say the least, with such repairs often exceeding the total value of many older, high-mileage vehicles.

Alternatively, some might find it cheaper to locate a replacement engine from a junkyard, as the cost associated with doing so is often less expensive than overhauling a vehicle’s current engine. This can be especially beneficial if you are up to the task of swapping the vehicle’s engine yourself, thereby eliminating any labor costs.

What About Metal Flakes in Your Transmission Fluid?

Unlike a vehicle’s engine oil, one can expect to observe some degree of metal shavings within their transmission’s fluid. This tends to be especially true if a vehicle has gone an extensive length of time without having its transmission oil changed.

These observable metal shavings are typically a product of normal internal gear mesh and are unlikely to indicate anything outside of normal wear. In fact, most transmission pans contain magnets to catch such debris.

However, one should keep their eye out for any large metal flakes, that are substantial enough to be pinched between your fingers, or that are sharp at their edges. Metal flakes of this type often indicate impending issues, due to abnormal wear. This is an issue that should be further diagnosed by a transmission specialist.

%d bloggers like this: